Products
About Us
Technical Support
Nov. 13, 2026
Share:A furnace quotation may list heating power in kW, while your electricity bill records energy in kWh. Those numbers answer different questions. To estimate operating consumption, you need a defined production cycle, a clear measurement boundary and the output produced during that period.
This guide explains how to compare electric heat-treatment furnaces on that basis. It covers a simple calculation example and the information to request from a supplier; it does not provide a universal consumption figure for every material or furnace.
Power describes the rate of electricity use. Energy describes the amount used over time. The U.S. Energy Information Administration explains the distinction between kW and kWh: one kilowatt sustained for one hour uses one kilowatt-hour.
A stated heating rating tells you about the specified heating equipment. Ask whether the quoted value covers only the heaters or the complete installation. Fans, pumps, cooling equipment and atmosphere generation may be listed separately.
| Figure | What it tells you | What to confirm |
|---|---|---|
| Rated heating power, kW | The specified heater power rating | Which components the rating includes |
| Average measured power, kW | Average electricity demand during a stated interval | Operating stage and measurement duration |
| Energy per cycle, kWh | Electricity used between defined start and end points | Meter boundary, load and starting condition |
| Specific energy, kWh/kg | Energy divided by the stated mass of output | Whether the denominator is loaded, processed or accepted product mass |
That multiplication assumes the stated power is drawn continuously for the entire interval. A furnace may require substantial heating during warm-up and a different average input while maintaining temperature. A controller's output percentage alone is not a calibrated electricity measurement for the whole installation.
Manufacturer data illustrate why the operating condition matters. Carbolite's RHF technical table lists maximum power and holding power separately. Those values describe that product range; they are not a conversion factor for a Rexin industrial furnace.
Multiplying a confirmed electrical rating by hours can describe an assumed full-power scenario. Label it as an assumption rather than measured consumption, and do not use it to promise production cost or energy savings.
For a meter recording cumulative energy, subtract the starting reading from the ending reading. If separate meters cover agreed auxiliary equipment, add their energy over the same interval. Qualified electrical personnel should select and install suitable metering.
Cycle energy (kWh) = ending meter reading − starting meter reading.
The following figures are invented only to demonstrate the arithmetic. Suppose a defined batch uses an average measured 40 kW during one hour of heating, 18 kW during two hours of holding, and 4 kW during half an hour of the included cooling stage.
The energy is (40 × 1) + (18 × 2) + (4 × 0.5) = 78 kWh. If the agreed denominator is 200 kg of accepted product, the result is 78 ÷ 200 = 0.39 kWh/kg. Neither figure is a Rexin specification, typical benchmark or customer result.
This example assumes each stage's average measurement includes the agreed equipment. Extra cooling, standby or utility equipment outside that boundary would require separate accounting. Keep part mass separate from baskets and fixtures when reporting product output.
Compare the same material, representative part geometry, loading arrangement, fixtures, temperature program and required product quality. A lower energy figure is not useful if it comes from a different treatment or fails the acceptance requirements.
State whether the test starts from a cold furnace or an already heated condition. Record loading, holding, cooling and idle periods explicitly. For continuous equipment, distinguish a steady production interval from a shift total that includes start-up and standby.
The U.S. Department of Energy's process-heating sourcebook discusses how equipment loading and heat losses affect energy per unit of production. Use that principle to check the proposed workload, rather than assuming either batch or continuous operation always consumes less.
For the holding stage, confirm when credited time begins. Our guide to heat-treatment soaking time explains why a completed controller timer may differ from the required exposure of the load.
Request a consumption estimate with its assumptions, or an agreed test report for representative production. Keep estimates and measured results clearly identified. Ask for the meter location, included auxiliaries, start and end conditions, cycle record, processed mass and accepted output.
If an energy-saving percentage is quoted, request the reference system and both test conditions. A percentage without a comparable baseline does not establish what your factory will save.
Use measured kWh and your applicable energy tariff for the electricity energy charge. Check demand charges, time-dependent pricing and other bill items separately. Electricity alone is also not the complete operating cost when fuel, protective gas or other services are required.
Send the material grade, part dimensions, batch weight or required output per shift, cycle requirements, operating schedule and available utilities. Ask the supplier to separate heating ratings, total connected requirements and estimated consumption under your stated conditions.
For a chamber application, review Rexin's box-type tempering furnace range alongside those process requirements. For an investment decision, the 24-month batch-versus-continuous cost guide puts energy into a wider comparison that also includes installation, maintenance and accepted output.
A useful consumption comparison ends with a reproducible measurement and a defined production result. That gives both buyer and supplier a basis for discussing performance beyond the nameplate power rating.
If you’re interested in our heat treatment furnaces or customized solutions, contact us for professional support and tailored quotations. We look forward to long-term win-win cooperation.