Dongguan Rexin Machinery Technology Co., Ltd.
Contact Us
News
Home

>

News

>

Heat Treatment Soaking Time: When Should the Hold Timer Start?

Heat Treatment Soaking Time: When Should the Hold Timer Start?

Nov. 12, 2026

Share:

Heat treatment soaking time is the period allowed for a specified treatment at temperature. The important question is what must reach that temperature before the clock starts: the programmed setpoint, a furnace sensor or the workpiece itself.

A controller showing the target temperature does not automatically establish that the whole load has received the required treatment. Define the timing rule from the applicable material instructions and approved process, then confirm that the furnace's measurement and timer configuration can implement it.

What is the difference between heating time and soaking time?

Heating time brings the furnace and load toward the required conditions. Soaking, also called holding or dwell, is the time assigned to the treatment stage. These terms need clear definitions in a production recipe because a programmed hold can include time while the material is still warming.

A material supplier may define holding time relative to the workpiece rather than the furnace display. For example, the Uddeholm Viking technical brochure, page 5, defines its hardening hold after the tool has heated through. That instruction concerns this tool steel and treatment; it is not a universal duration or recipe for other alloys.

Which temperature should trigger the hold timer?

Separate three values when reviewing a cycle. The setpoint is the requested temperature. The process value is the reading used by the controller. A load temperature is a measurement associated with the product. They may follow different paths during heating.

Timing reference What it establishes What still needs checking
Programmed setpoint reaches its target The scheduled ramp has ended Whether the furnace and relevant load locations have reached their required conditions
Furnace process value enters a defined band The monitored furnace measurement meets that band Whether this measurement is the approved basis for starting the treatment
Specified load measurements meet the requirement The required measured load locations satisfy the start condition Sensor placement, measurement validity and the remaining time and temperature requirements

The approved process determines which reference is appropriate. Do not substitute a furnace reading for a required product measurement simply because it is easier to obtain.

Why can a completed controller hold give insufficient time at temperature?

Consider an illustrative timing example, not a recommended heat treatment. Assume an approved procedure requires 30 minutes after its specified load measurements enter the permitted temperature band. The furnace control sensor reaches its target at 09:00, but the required load condition is not satisfied until 09:18.

If the timer runs from 09:00 to 09:30, only 12 minutes remain after the load meets the start condition. A full 30-minute period from 09:18 would end at 09:48, assuming all other procedure requirements remain satisfied. The missing 18 minutes comes from the timing reference, not an arithmetic error in the controller.

This example explains why a nominal hold duration and an accepted treatment record are different things. A completed program should be assessed against the specified conditions, including how deviations are handled.

Does holdback or guaranteed soak solve the problem?

A holdback function can delay or pause program progression when a monitored temperature differs too far from its target. Eurotherm's ramp-and-soak guidance explains how this can stop a soak segment starting before the measured temperature is sufficiently close to the target.

The function's name does not identify which sensor it watches. The Nabertherm Series 500 manual, section 10.7, describes different holdback modes with different behavior. Some functions depend on the controller model, selected zones and charge-control configuration. These are manufacturer examples, not confirmation that every Rexin furnace has identical functions.

Check the installed controller's manual and approved configuration. A timer waiting for the furnace sensor cannot, by itself, prove that an unmeasured product location has reached temperature.

What should be recorded during cycle validation?

Eurotherm also explains that sensors on or inside the work may be needed to confirm the material's temperature-time exposure. Use a measurement plan appropriate to the product and process; sensor location is part of the evidence, rather than an arbitrary place to attach a probe.

Record the material and part dimensions, loading arrangement and fixtures, recipe revision, sensor identities and locations, temperature trends, soak-start event and timer behavior. Document interruptions and temperature excursions for review under the applicable procedure rather than automatically adding an assumed amount of time.

For related measurement terminology, see furnace temperature uniformity versus control accuracy. A stable control display, a uniform working zone and the product's heating history answer different questions.

What should buyers specify when requesting a furnace?

Include the material process specification, normal and maximum load, part dimensions, required temperature band, soak-start rule, recording needs and cooling requirements. Ask which measurement starts the timer and what the system does if that measurement leaves the permitted band.

Rexin's chamber and box-type tempering furnaces provide a starting point for an equipment discussion. Confirm the proposed sensor arrangement, controller functions and representative-load acceptance plan for the actual application; a maximum-temperature rating alone does not define a qualified cycle.

Do You Have Further Questions?

If you’re interested in our heat treatment furnaces or customized solutions, contact us for professional support and tailored quotations. We look forward to long-term win-win cooperation.